Huatao Group-Vibrating Screen Technology Solution and Service for Quarry & Mining Industry Since 2008.
Answer
Yes—PU dewatering panels are widely used in sand and gravel washing because they handle high water volume and abrasive sand well. ๐๏ธ
Direct Answer
They resist abrasion, reduce blinding, and deliver consistent dewatering. For high water volume, choose ridge-profile panels with 0.5–2.0 mm slots and 90–95 Shore A hardness.
Technical Parameters
• Slot size: 0.5–2.0 mm
• Hardness: 90–95 Shore A
• Open area: 30–40%
• Profile: ridge or flat-top
• Fixing: pin or rail system
Selection Advice
For coarse sand, use ridge-profile panels in the first section. For fine sand, use flat-top panels with smaller slots. Match panel size to your washer deck.
Practical Tips
Control feed rate to avoid overload.
Keep spray nozzles clean.
Check panels after high-production shifts.
Use wear-resistant grade for sharp sand.
Data / Case
A sand washing plant using PU dewatering panels achieved 15% lower moisture content and reduced panel replacement cost by 30% versus rubber.
๐ง Email: annie.lu@huataogroup.com
๐ฑ Mobile: +86 18032422676 (WhatsApp/WeChat)
๐ Visit: www.tufflexscreen.com
Answer:
๐งน Streaking usually means part of the blade is not maintaining effective contact with the belt.
A single narrow streak can indicate a damaged blade segment, trapped particle or local belt groove. Multiple repeated streaks may indicate uneven blade wear or an incorrect cleaning width. A broad dirty band often points to low tension or the wrong cleaner for the material.
Check:
• chipped or grooved blade edge
• uneven tension left-to-right
• bent mainframe
• blade segments seized with buildup
• belt cupping or surface damage
• incorrect pole alignment
• insufficient tension
• material trapped behind blade
• cleaner width versus material path
Do not immediately tighten the cleaner. Clean the blade, inspect the edge and verify geometry first.
If the primary cleaner removes coarse carryback but leaves a uniform thin film, it may actually be doing its intended job. A secondary cleaner is designed to remove the finer residue after the belt leaves the pulley.
Photographing the dirty belt pattern is useful because the shape of the streak often indicates where to inspect first.
๐ง Email: annie.lu@huataogroup.com
๐ฑ Mobile: +86 18032422676 (WhatsApp/WeChat)
๐ Visit: www.tufflexscreen.com
Answer:
๐ชจ Highly abrasive material requires attention to blade compound, usable wear volume, cleaner structure and belt speed.
Heavy-duty engineered PU remains a common primary-cleaner choice because it combines wear resistance with impact resilience. Commercial heavy-duty PU cleaners are available around 90 Shore A, although exact hardness should be selected according to the application.
For extreme abrasion, tungsten-carbide-tipped designs can provide longer edge life. But they should only be used where the belt surface, splice and cleaner geometry are suitable.
Selection priorities include:
• abrasion level/material hardness
• tonnes per hour
• maximum lump size
• belt width and speed
• pulley diameter
• belt splice
• hours of operation
• desired maintenance interval
Do not select only by the thickest blade. A large wear volume is valuable only if the cleaner maintains the correct contact geometry throughout that wear.
For hard-rock mines, it is often more economical to use a robust PU primary cleaner for bulk removal and an engineered secondary cleaner for fine residual carryback.
๐ง Email: annie.lu@huataogroup.com
๐ฑ Mobile: +86 18032422676 (WhatsApp/WeChat)
๐ Visit: www.tufflexscreen.com
Answer:
๐ง Wet and sticky material usually needs a system approach, not simply a harder scraper.
A resilient PU primary cleaner is commonly used to remove the bulk carryback at the head pulley. For sticky clay, wet coal fines or moist mineral concentrates, the blade needs enough flexibility to maintain contact without allowing a sticky layer to pack behind it.
However, the primary cleaner will rarely remove every thin wet film. A secondary cleaner installed after the head pulley is often required.
Depending on the application, segmented carbide/PU blades, specialty low-adhesion compounds, wash systems or additional cleaning stages may be considered.
Check:
• moisture percentage and stickiness
• clay content
• belt texture and cover condition
• material temperature
• belt speed
• chute buildup
• availability of wash water
• carryback particle size
Avoid over-tensioning the primary blade to chase the final wet film. Let the primary cleaner remove bulk material and use the secondary stage for residual fines.
Also inspect the chute. If scraped wet material cannot fall freely, buildup can push material back onto the belt.
๐ง Email: annie.lu@huataogroup.com
๐ฑ Mobile: +86 18032422676 (WhatsApp/WeChat)
๐ Visit: www.tufflexscreen.com
Answer
Routine maintenance helps maintain separation performance, prevent unexpected downtime and identify mechanical problems before they become serious. The inspection schedule should follow the equipment manufacturer's manual and the actual operating environment. ๐ ๏ธ
Magnetic surface and drum: Check for accumulated material, wear, damage or buildup that could interfere with material movement.
Bearings and drive system: Inspect for abnormal noise, vibration, overheating, lubrication issues and changes in drum rotation.
Feed and discharge points: Make sure the feed is distributed evenly and the magnetic and non-magnetic products can discharge freely.
Magnetic system: For electromagnetic equipment, check the specified electrical readings, cooling arrangements and relevant alarms. For permanent-magnet systems, inspect for physical damage and monitor magnetic performance when appropriate.
Safety guards and controls: Ensure protective covers, emergency stops and interlocks are functioning as designed.
There is no universal inspection interval. Operators may carry out visual checks each shift, with more detailed inspections scheduled according to operating hours, manufacturer recommendations and site maintenance procedures.
For a useful performance baseline, record feed rate, product iron content, recovery where measurable, motor current and relevant operating settings.
If product quality deteriorates while the feed characteristics remain stable, inspect the equipment and compare operating data with the baseline.
Magnetic separation performance depends on both the magnetic system and operating conditions, so maintenance should cover the entire process rather than focusing only on the magnet.
Important safety note: Isolate electrical and mechanical energy according to site lockout/tagout procedures before cleaning, removing blockages or working near moving parts. Strong magnetic fields can also affect some medical devices and attract ferrous objects unexpectedly.
๐ง Email: annie.lu@huataogroup.com
๐ฑ Mobile: +86 18032422676 (WhatsApp/WeChat)
๐ Visit: www.tufflexscreen.com
Answer
If iron remains in the non-magnetic product, the cause may be an unsuitable magnetic field, poor feed distribution, insufficient particle liberation, excessive feed loading or iron impurities that are too weakly magnetic for the installed equipment. ๐ง
1. The magnetic field is unsuitable. A low-intensity separator may capture magnetite effectively but leave some weakly magnetic minerals behind. Consider testing a high-intensity or high-gradient system if mineralogical analysis supports this choice.
2. The feed layer is too thick. Particles buried within a deep material bed may not experience sufficient magnetic force. Reduce loading or improve feed distribution and evaluate the change in iron removal.
3. The feed contains mixed particle sizes. Fine iron-bearing particles may behave differently from coarse particles. Screening or classification may improve consistency in some applications.
4. The target minerals are not liberated. Iron-bearing minerals locked inside larger composite particles may not separate cleanly until suitable grinding or other preparation is performed.
5. Operating conditions have changed. Check feed rate, moisture, drum speed, slurry flow and the condition of the magnetic assembly.
These factors are recognized considerations in magnetic separator design and mineral-processing optimization.
Take representative feed and product samples. Measure their iron content using the same analytical method, and record the feed rate and operating settings. If possible, examine the mineralogy of the remaining iron-bearing particles.
For example, if a silica sand plant captures visible magnetite but still fails its iron specification, the remaining impurity may be weakly magnetic hematite, iron-bearing mica or iron coatings on quartz grains. Simply increasing the magnet strength may not solve every case.
The best adjustment should be supported by testing and should improve product quality without causing unacceptable material loss or throughput reduction.
๐ง Email: annie.lu@huataogroup.com
๐ฑ Mobile: +86 18032422676 (WhatsApp/WeChat)
๐ Visit: www.tufflexscreen.com
Answer
Magnetic separator capacity depends on the equipment design and the characteristics of the feed. Increasing feed rate without checking separation performance can allow magnetic particles to escape into the non-magnetic product. ๐
1. Equipment dimensions: Drum diameter, drum width, roll configuration and effective separation area influence how much material can be processed.
2. Magnetic field: The field strength and gradient must be appropriate for the target minerals.
3. Feed characteristics: Particle size, density, moisture, magnetic susceptibility and liberation all affect separation behavior.
4. Feed distribution: Uneven loading or a thick material layer can prevent some particles from approaching the effective magnetic zone.
5. Operating conditions: Drum speed, slurry flow, feed concentration and discharge arrangements can influence capacity and separation quality.
Magnetic separation involves competition between magnetic forces and other forces acting on particles. As feed loading increases, particles may have less opportunity to contact or remain within the effective magnetic zone.
Keep the feed rate steady and distribute material evenly.
Confirm that particle size and moisture are within the equipment's operating range.
Inspect the magnetic surface and discharge arrangements for buildup.
Check whether the magnetic field is suitable for the target impurity.
Test incremental feed-rate increases while monitoring product purity and recovery.
A useful initial equipment inquiry should include the required throughput in tonnes per hour (t/h), feed particle size, moisture or slurry concentration, target magnetic minerals, current impurity level and required product quality.
There is no reliable universal throughput figure for all magnetic separators. A small unit treating fine weakly magnetic particles may have a very different capacity from a large drum recovering coarse magnetite.
The correct target is the required capacity while maintaining acceptable separation efficiency, not maximum feed rate alone.
๐ง Email: annie.lu@huataogroup.com
๐ฑ Mobile: +86 18032422676 (WhatsApp/WeChat)
๐ Visit: www.tufflexscreen.com
Contact: Annie Lu
Tel: +86 18032422676
E-mail: manager11@huataogroup.com
Address: Zhonghua North Street, Shijiazhuang, Hebei, China