Huatao Group-Vibrating Screen Technology Solution and Service for Quarry & Mining Industry Since 2008.
Most primary belt cleaners underperform because the blade isn't touching the belt properly, or because tension has gone slack since installation. Contact geometry comes first, then tension, then compound. A blade that reaches only three quarters of the belt width is a worn blade at any price, and a cleaner mounted past the tangent point is polishing a belt it was meant to scrape.
| Item | Description |
|---|---|
| Function | Scrapes the bulk of carryback off the belt at the head pulley |
| Material | Polyurethane, rubber, carbide or ceramic blade on a steel frame |
| Application | Troughed conveyors in mining, aggregates, coal, cement and ports |
| Service Life | Set by abrasion, belt speed, splice type and tension discipline |
| Benefits | Clean return strand, less spillage, less dust, longer roller and belt life |
It scrapes. That's the whole job, and it's worth saying plainly because so much else gets loaded onto the device. A primary cleaner doesn't contain the load, cushion impact, steer a drifting belt or dry the cover. It removes the bulk of the carryback before the belt reaches the return strand, and everything else belongs to other hardware.
Position is what makes the scraping possible. The head pulley is the only place on a conveyor where the belt is loaded and backed by something rigid at the same time. Past the tangent point the belt runs free. A blade pressed there pushes the belt away rather than cutting the film, and the cleaner becomes an expensive way to polish rubber.
That geometry explains most performance complaints, and it's the reason a plant can replace blades for two years without improving cleanliness by a measurable amount. The Conveyor Belt Cleaner / Scraper range exists in primary and secondary forms because the two stages do different work at different points on the same pulley.
A primary cleaner at the head pulley, where the belt is still round and still supported. Off the pulley, the same blade bends the belt instead.
The blade is a wedge, and the film of material on the belt is what gets sheared. Three conditions make that happen, and they're sequential.
Support comes first. On the pulley face, steel sits behind the belt, so the blade can compress the cover by a fraction of a millimetre and cut. That compression is the whole mechanism. Lose the support and the blade has nothing to cut against.
Angle comes second. A shallow attack angle rides on top of the film. A steep angle digs into the cover, heats the tip and shortens its own life. Primary blades are usually set with a slight trailing angle, and the bracket is machined for a specific pulley diameter. Re-drill that bracket for a different pulley and the angle becomes an accident.
Force comes third. Enough pressure to hold contact through splice impacts and load swings, and not enough to generate heat. That's a narrow band, which is why springs, gravity arms and air cylinders are all compromises of a different kind rather than solutions of a different quality.
Then wear erodes all three. As the tip shortens, the angle drifts and pressure falls. A Conveyor with a cleaner that was perfect at commissioning can be mediocre within six months without a single part failing.
The return strand changes first. Fines stop packing onto Conveyor Idlers & Rollers, rollers stay round, and a belt that had been drifting settles down. That sequence, from cleaner to roller to tracking, is one most plants discover by accident.
Dust follows. Carryback released under the conveyor becomes airborne dust along the entire route. Material that stays on the belt until the discharge point never becomes dust in the walkway, which matters more every year as exposure limits tighten.
Belt and lagging life improve without anyone noticing. A clean bottom cover runs cooler. A belt tracking straight across a pulley wears lagging evenly rather than grinding a groove at one edge, and lagging without a groove keeps its grip on the drive.
Then there's the arithmetic that survives a budget meeting. On a 1,200 mm belt at 2.5 m/s, a 1 mm film of material at 1.6 t/m³ returns roughly 17 t/h. Product already paid for, travelling backwards, abrading the conveyor as it goes.
Every conveyor that discharges onto a return strand needs one of these. The installations where it matters most share three features: tonnage high enough to wear a blade within a year, material abrasive or wet enough to defeat a slack blade, and a return run long enough to accumulate damage quietly.
Mining plants hit all three. The belt leaving a crusher carries sharp material and clinging fines. The belt arriving at a screen carries the same material, often wetter. Aggregate plants run drier and faster, so abrasion dominates and dust becomes the visible symptom. Coal handling brings wet sticky fines that smear rather than release, and a dry blade has limited authority over a smeared film.
Load points need separate protection. An Impact Bed under the chute keeps the belt stable where material lands, so the load line stays where the chute put it. A Guide Trough straightens the stream before it settles. Both cut what reaches the cleaner and even out blade wear across the width.
| Compound | Abrasion | Splice behaviour | Heat | Cost | Best fit |
|---|---|---|---|---|---|
| Polyurethane | Good | Deflects, keeps scraping | Moderate | Moderate | Most mining and aggregate duty |
| Rubber | Moderate | Very forgiving | Moderate | Low | Worn or cupped belts, low speed |
| Tungsten carbide | Very high | Brittle, chips on bolt splices | High | High | High tonnage, vulcanised splices |
| Ceramic | Very high in wet duty | Brittle, needs a flat belt | High | High | Slurry-wet process lines |
Price per blade and cost per tonne cleaned are different numbers. A carbide blade that chips in month two on a bolted splice costs more than three urethane blades that survive a year. A rubber blade changed four times a year costs more in labour than a urethane blade changed twice, unless the belt is worn enough that only rubber maintains contact.
Polyurethane Conveyor Belt Cleaner Blades sets out hardness against duty, which is more useful than a single number quoted out of context. Hardness alone doesn't predict performance. Tip profile and mounting angle do more.
Iron ore at high tonnage is dry, sharp and abrasive. Blade wear is the constraint, and it's predictable, so the specification leans toward carbide or heavy urethane plus a tension system that allows a fast change inside a shutdown.
Wet coal is the opposite problem. Wear isn't the constraint; adhesion is. A dry blade skims a smeared film and leaves most of it behind, and whatever escapes cakes onto return rollers within days. The answer is a secondary cleaner and better containment, with Conveyor Belt Skirting keeping the load centred so the film is even across the width.
Same device, opposite bottlenecks. Buying the harder blade in the coal plant buys nothing. Buying the softer blade in the iron ore plant moves cost from procurement to labour.
| Industry | Material | Challenge | Priority |
|---|---|---|---|
| Iron ore | Dry abrasive lump and fines | Tip wear at tonnage | Compound, tension |
| Copper | Wet abrasive residue | Film after primary pass | Secondary stage |
| Coal | Wet sticky fines | Smearing, build-up | Containment |
| Gold | Fine abrasive, wet | Thin film on polished cover | Contact geometry |
| Aggregates | Dry crushed stone | Dust and fast wear | Angle, suppression |
| Cement | Hot, fine, abrasive | Heat plus abrasion | Compound, distance |
| Ports | Mixed dry bulk | Speed, short windows | Tension system |
Belt speed. Above roughly 4 m/s, urethane options narrow and heat limits performance. Below 2.5 m/s almost anything works, and price should lead the decision.
Splice type. A vulcanised, squared splice lets you run carbide. A bolted or hinged splice doesn't, and no amount of tension tuning changes that.
Access. If a blade change has to fit a four hour window, a quick-release tension system beats a longer wearing blade. If the conveyor runs a year between stops, buy wear life.
Belt condition. A cover worn into grooves needs a softer blade that follows the profile. A new belt with a flat cover takes a hard tip happily. Conveyor Belts covers cover grades for anyone specifying a replacement, and a Belt Conveyors reference helps when a whole line is in scope rather than one cleaner.
| Information | Why it matters |
|---|---|
| Belt width, speed, cover thickness | Blade size and speed rating |
| Head pulley diameter, face width | Blade profile and geometry |
| Splice type | Rules out brittle compounds |
| Material and moisture | Abrasion and adhesion |
| Frame drawing or photo | Whether the frame can be reused |
| Tension system | Spring, gravity, air or torsion |
| Annual consumption | MOQ, packaging, shipping |
Ask five questions before a trial order. Can you manufacture to our drawing? Can you supply material reports? Can you support OEM replacement? Do you have export experience in our region? Can you recommend tension settings for our belt speed? Clear answers to all five beat a low price with vague answers.
On drawings, five dimensions do most of the work: overall length, hole pattern, tip profile, blade thickness and wear allowance. A sketch with those removes the commonest cause of wrong parts.
Tension hardware decides whether a worn tip still reaches the belt. A relaxed spring ends the conversation early.
| Problem | Cause | Solution |
|---|---|---|
| Wear at one end | Frame out of parallel; uneven lagging | Square the frame, check lagging |
| Wear to a wedge | Wrong angle; over-tensioned | Reset angle and tension |
| Polished belt, no removal | Mounted past the tangent point | Move back onto the pulley face |
| Cleaning stops in a month | Tension lost after run-in | Re-tension, then monthly checks |
| Chipped tip | Carbide on a mechanical splice | Change compound or skive |
| Packing behind the blade | Wet material; tight pocket | Clear pocket, review chute |
| Uneven cleaning | Cupped belt or crowned pulley | Fix belt or lagging first |
The pattern is the diagnosis. Wear at one end means alignment. Wear to a wedge means angle. Fast even wear means tension. No wear at all means the blade isn't touching, and that's a mounting problem every time.
Daily: watch the discharge. Material throwing wide of the chute usually means one section has stopped being cleaned.
Weekly for the first month, monthly after: tension, blade wear against the limit, frame bolts, and the pocket behind the blade. A pocket packed with fines stops the blade pivoting, and a cleaner that can't pivot stops cleaning. That's the most common avoidable failure on site, and it takes ten minutes to prevent.
Monthly: pulley lagging and the belt cover under the blade. Both wear, and both change what a blade can achieve.
Replacement: the wear limit, not the calendar. When the tip can't reach the belt at full tension, the blade is finished. Keep a spare set per critical conveyor. A stopped cleaner becomes a stopped conveyor eventually, and the second event costs far more than the first.
Customer type: aggregates quarry, two stage crushing and screening.
Ore type: crushed granite, dry and abrasive.
Operating conditions: 1,000 mm belt, moderate speed, bolted mechanical splice, one primary cleaner on a chute-mounted frame.
Problem: carryback returning to the tail pulley, fines building under the conveyor, and blades replaced every few months without any improvement in cleanliness. Blades wore into a wedge well before the wear limit.
Solution: the mounting sat past the tangent point and the chute wall flexed under load, so the blade alternated between scraping and floating. Frame re-mounted to the conveyor structure, squared to the belt centre line, tension reset to the supplier's figure, compound changed to a softer urethane suited to the bolted splice.
Result: even wear across the width, longer intervals, and a return strand that stayed visibly cleaner between inspections. The blade wasn't the problem, and changing it repeatedly never was going to be the answer.
Why isn't my primary cleaner removing material?
Usually because the blade isn't in contact. It sits past the tangent point where the belt deflects, or the frame is out of parallel and one end rides clear. A chalk line across the belt shows which within minutes. If chalk survives at one edge, the fault is geometry, not compound.
How much tension is correct?
The manufacturer's figure for your blade and belt width, set by their method, usually deflection or spring compression. Not by feel. Re-check after the first shift and again after the first week, because blades bed in and belts settle. Over-tension wears the cover; under-tension skims.
Urethane or carbide?
Urethane for most mining and aggregate conveyors, especially with mechanical splices or a worn cover. Carbide for high tonnage, high speed and vulcanised splices, where the belt gives the tip a stable surface. Carbide on a bolt splice chips, and a chipped tip stops cleaning that section immediately.
Can I keep the existing frame?
Often yes, if it's straight, the mounting is square and the bracket angle matches the pulley. Frames fail when they're bent, corroded at the bolt holes, or bolted to a surface that flexes. Measure the frame and pulley before ordering, or the new blade will wear like the old one.
Do I need a secondary cleaner?
If the return strand matters, yes. A primary removes the bulk and leaves a film. A Mining Secondary Belt Cleaner removes that film. Without it, the film reaches the rollers, cakes, crowns them and starts a tracking problem that gets blamed on the belt.
Does a cleaner damage the belt cover?
Only when over-tensioned or set at the wrong angle. A correct blade removes material and leaves the cover lightly polished. Too much pressure generates heat, wears the cover and can lift the tip at speed. A dark polished stripe under the blade is heat, not efficiency.
How often should blades be replaced?
When the tip can't reach the belt at full tension, or wear reaches the maker's limit. A measurement, not a date. On abrasive duty at high tonnage, expect several changes a year. Keep a spare set on site for conveyors that can't be stopped for a blade.
What should I include in an enquiry?
Belt width and speed, head pulley diameter and face width, splice type, material description with moisture, and a frame drawing or dimensioned photo. Add the tension system and annual consumption. That's enough for a supplier to quote a blade that fits and works.
Fix the geometry before spending money on compound. Put the blade where the belt is supported, square the frame, set tension to spec and re-set it after run-in. Then keep checking, because nothing about a cleaner fails loudly.
Compound follows from speed, splice and material. It's a real decision, and it's the second one. Plants that start there tend to own a drawer full of blades that didn't help.
And finish the job downstream. Secondary cleaning, sealed transfer points, clean return rollers. That's what turns a fortnight of good cleaning into a season of it.
Related Products
Related Technical Guides
Related Buyer Guides
Related Comparison Articles
Annie Lu
Email: annie.lu@huataogroup.com
WhatsApp/WeChat: +86 18032422676
Website: www.tufflexscreen.com