Key Takeaways
- Suspension height is the single most tunable capture variable: magnetic pull decays sharply with distance, so millimetres matter.
- Start at 0.2–0.3 × belt width (200–300 mm for a 1,000 mm belt), then add burden-depth correction.
- Measure from the magnet working face to the target object's deepest position — not to the bare belt.
- Capture is a time budget: belt speed above 2.5–3.0 m/s makes an electromagnetic circuit mandatory.
- The magnet face should be 200–400 mm wider than the belt to catch edge-positioned steel.
- Dust and ore build-up on the magnet face silently widen the gap — clean and test on a fixed schedule.
Summary Table
|
Item
|
Description
|
|
Function
|
Suspends above the conveyor and continuously lifts ferrous tramp metal out of the burden onto a self-cleaning discharge belt
|
|
Working gap rule
|
0.2–0.3 × belt width; burden depth + 50–100 mm safety clearance; typical range 150–450 mm
|
|
Field type
|
Permanent (shallow–medium burden) vs electromagnetic (deep burden, fast belts, heavy pieces)
|
|
Belt speed limit
|
Best capture at 1.5–2.5 m/s; above 3.0 m/s a deep-penetration electromagnet is required
|
|
Width rule
|
Magnet face 200–400 mm wider than the conveyor belt
|
|
Service life
|
Magnetic circuit 10+ years; discharge belt, rollers and chute liners are the wearing items
|
|
Benefits
|
Protects crushers and screens, cuts liner replacement, reduces unplanned downtime
|
Market Watch — November 19–20, 2026
The setting you choose for suspension height has a direct cost story behind it this week:
- Copper repricing: LME copper fell 5.7% in a single session to $12,471/t, its lowest since April, as the "AI demand" trade unwound; tin dropped 5% to $42,792/t and zinc fell 5.2% to $3,484/t. Cheaper metal softens replacement budgets but does not change the physics of tramp iron protection.
- Gold at a one-year low: Spot gold fell 3.2% to $3,725.86/oz and silver 5.0% to $45.03/oz after central-bank minutes signalled further rate hikes — gold concentrator operators watching margins should note that crusher damage from one missed bolt can erase weeks of recovery gains.
- Iron ore still under pressure: Spot iron ore held near ¥645.89/t (down about 20% year-on-year). Marginal-cost operations are delaying capital projects, which pushes protection of existing crushers and conveyors — instead of new equipment — to the top of the list.
- Wear-parts cost signal: Natural rubber spot is up roughly 23.5% year-on-year, a reminder that polyurethane-based wear components such as Polyurethane & Rubber Screen Panels keep costing-in less than rubber as feedstock prices climb.
Long-cycle investment continues: A $4.5 billion brownfield copper expansion was approved with a new primary crusher, overland conveyor and ~115,000 t/d of incremental concentrator capacity, and a $551 million copper project broke ground on early works. Every new crushing line of this type ships with suspended magnetic separation ahead of the crusher — suspension height will be a commissioning parameter, not an afterthought.
![How Close Should a Self-Cleaning Overband Magnet Be to the Conveyor Belt for Maximum Tramp Iron Capture? 1]()
Conclusion
The question "how close should the magnet be?" has a disciplined answer, not a guess: start at 0.2–0.3 × belt width, add burden-depth correction with a 50–100 mm clearance floor, measure from the working face to the deepest position the steel can occupy, and let belt speed decide whether a permanent or electromagnetic circuit is physically capable of the lift. Set the hard collision floor first, optimise capture above it, keep the magnet face wider than the belt, and guard the setting with a monthly gap log — because height drift, not magnet failure, is what quietly leaks tramp iron into your crushers. Get the gap right and every downstream wear part, from liners to Conveyor Belts, lasts exactly as long as its engineering says it should.
HUATAO Group supplies mining wear parts and separation equipment — self-cleaning and electromagnetic overband separators, magnetic drums and rollers, screen panels, crusher wear parts and conveyor protection components — with OEM manufacturing to drawing and export experience across mining projects worldwide.
![How Close Should a Self-Cleaning Overband Magnet Be to the Conveyor Belt for Maximum Tramp Iron Capture? 2]()
Related Articles
Related Products
- Iron Magnet
- Self-Cleaning Electromagnetic Separator
- Magnetic Drum
- Heavy-Duty Conveyor Impact Bed
- Conveyor Belt Tracker
Related Technical Guides
- Magnetic Separation Process Equipment
- Conveyor Process Equipment
- Crushing Process Equipment
- Improve Fine Screening Efficiency with Polyurethane Screen Panels
- Hydrocyclone Wear: Root Causes, High-Wear Zones & Material Solutions
Related Buyer Guides
- Which Manufacturer Offers High-Quality Polyurethane Tufflex Wire Screens for Mining?
- How Do I Choose the Right Rubber Belt for a Vacuum Belt Filter?
Related Comparison Articles
- Polyurethane Screen vs Rubber Screen vs Wire Mesh: A Complete Comparison Guide
- Self-Cleaning Screen vs Traditional Woven Wire Mesh: Which One Should You Choose?
Contact Us
Contact: Annie Lu
Email: annie.lu@huataogroup.com
Phone / WhatsApp: +86 180 3242 2676
Website: http://www.tufflexscreen.com
We warmly welcome customers from around the world to contact us and establish mutually beneficial partnerships.