loading

Huatao Group-Vibrating Screen Technology Solution and Service for Quarry & Mining Industry Since 2008.

How Do I Size a Self-Cleaning Suspended Magnet for a 1,200 mm Conveyor at 800 t/h?

Quick Answer

For a 1,200 mm troughed conveyor carrying 800 t/h of crushed ore at about 2.0 m/s, specify a self-cleaning suspended magnet with a face roughly 1,400 mm wide, hung about 350 mm from the belt surface — around 240 mm above a bed that averages 60–110 mm deep — with a rated field of at least 70 mT at that gap, a cleaning-belt drive near 4 kW, and a belt speed kept at or below 4.5 m/s. Tonnage alone never sizes the unit; burden depth, gap and exposure time do.

Key Takeaways

  • Size by volumetric burden, not by tonnage: 800 t/h of iron ore at 2.0 t/m³ and 2.0 m/s gives a bed only 60–110 mm deep, which changes the whole specification.
  • The magnet face should be 100–200 mm wider than the belt on each side; a flush-width magnet leaks edge iron on every troughed belt.
  • A 1,200 mm-class self-cleaning unit is typically rated at 350 mm suspension height, ≥70 mT (700 G) at that gap, ≤300 mm burden and ≤4.5 m/s belt speed, with about 4 kW of cleaning-belt drive.
  • Define the hardest target iron — minimum mass, shape, orientation and worst-case depth — before comparing any two supplier quotations.
  • Above roughly 200 mm design burden, step up from ferrite to rare-earth or electromagnetic circuits; below that, a permanent circuit runs with zero field power.
  • Budget the structure as part of the magnet: a 1,200 mm-class unit weighs about 2.3 tonnes, and suspension points should be designed for roughly twice the static load.
How Do I Size a Self-Cleaning Suspended Magnet for a 1,200 mm Conveyor at 800 t/h? 1

What Is a Self-Cleaning Suspended Magnet and Where Does It Sit in the Circuit?

A self-cleaning suspended magnet — usually called an overband or cross-belt separator — is a permanent or electromagnetic block hung above a conveyor belt, wrapped in its own short motor-driven belt that continuously carries captured iron out of the field into a side chute. It sits in the conveying stage of the mineral processing chain, and its job is to intercept ferrous steel before it reaches crushing or screening equipment. Position it over the head pulley for the strongest capture, or cross-belt over the inclined run where headroom allows.

In a typical circuit the magnet protects the line between Belt Conveyors and the primary crusher: ore leaves a bin or feeder, travels under the suspended unit, and any bolt, drill steel or liner fragment riding the burden is lifted into the discharge chute. What survives the magnet meets the Jaw Crusher or Hydraulic Cone Crusher — machines whose jaw plates and mantles are exactly the parts tramp iron destroys. That is why magnet sizing and Crusher Wear Parts budgets are two lines of the same spreadsheet.

The equipment family itself is broader than one machine. HUATAO supplies the full Magnetic Separators range, from the Iron Magnet plate units to the Electromagnetic Overband Separator and the Self-Cleaning Electromagnetic Separator used on deep-burden, high-tonnage conveyors, plus downstream Magnetic Drum and roller units for product purification. Sizing the suspended unit correctly keeps the whole family working as designed.

Case Study

Customer Type: Iron ore mine, primary crushing line.

Ore Type: Crushed hematite, ~2.0 t/m³ loose, 150 mm top size.

Operating Conditions: 1,200 mm belt, 800 t/h, 2.0 m/s, measured bed 95–120 mm, 24/7 operation.

Problem: The existing ferrite unit was specified by belt width alone, with a face equal to the belt and a gap drifted to 420 mm after a gantry modification. Capture of 0.5–1 kg steel was visually under half; the cone crusher absorbed two tramp-iron events a year, each costing liner damage and 10–14 hours of downtime.

Solution: Resized by the six gates: 1,400 mm rare-earth self-cleaning unit, rated 350 mm gap with ≥70 mT, 4 kW drive, 50–60° lined discharge chute, acceptance gauss survey written into the purchase order, suspension redesigned for 2× static load.

Result: Verified capture of the 0.5 kg target at bed bottom rose from roughly 55% to above 95% in a test-piece audit; crusher tramp-iron events fell from two per year to zero across 14 months; collected steel averaged 260 kg per day, confirming the 0.01–0.03 kg/t estimate used for sizing. Downtime avoided was conservatively valued at more than ten times the magnet replacement cost in the first year.

Related Articles

Related Products:

  • Self-Cleaning Electromagnetic Separator
  • Electromagnetic Overband Separator
  • Magnetic Drums & Rollers
  • Heavy-Duty Conveyor Impact Bed
  • Conveyor Belt Tracker
  • Conveyor Guide Trough

Related Technical Guides:

  • Hydrocyclone Wear: Root Causes, High-Wear Zones & Material Solutions
  • Improve Fine Screening Efficiency with Polyurethane Screen Panels
  • Flotation Cell Rotor and Stator Wear Parts: How They Control Recovery, Flow and Maintenance Cost

Related Buyer Guides:

  • How Do I Choose the Right Rubber Belt for a Vacuum Belt Filter?
  • Which Manufacturer Offers High-Quality Polyurethane Tufflex Wire Screens for Mining?

Related Comparison Articles:

  • Polyurethane Screen vs Rubber Screen vs Wire Mesh: A Complete Comparison Guide
  • Self-Cleaning Screen vs Traditional Woven Wire Mesh: Which One Should You Choose?

How Do I Size a Self-Cleaning Suspended Magnet for a 1,200 mm Conveyor at 800 t/h? 2

Contact Us

Contact: Annie Lu

Email: annie.lu@huataogroup.com

Phone / WhatsApp: +86 180 3242 2676

Website: http://www.tufflexscreen.com

We warmly welcome customers from around the world to contact us and establish mutually beneficial partnerships.

prev
Self-Cleaning Magnet Keeps Picking Up Manganese Steel —
recommended for you
Get in touch with us
Customer service