Huatao Group-Vibrating Screen Technology Solution and Service for Quarry & Mining Industry Since 2008.
Yes. PU mesh panels can be installed on many existing Stack Sizer machines, provided the panel dimensions, fixing arrangement, tensioning system and aperture specification match the existing equipment. Stack Sizer machines already use polyurethane screening media, so the question is not whether PU can work but whether a specific alternative panel fits a specific deck. Confirm machine model, panel dimensions, edge profile, tensioning direction, aperture size and polyurethane formulation before ordering, and trial one deck before converting the whole machine.
PU is already standard on Stack Sizers.
Compatibility is more than panel size: edge profile, tensioning and fixing points matter.
Aperture specification is a separate check from physical fit.
Polyurethane properties must suit mineral, feed, slurry and water conditions.
Modification is often unnecessary but must be confirmed per machine.
Trial before full conversion with cost per tonne as the decision metric.
| Item | Description |
|---|---|
| Function | Replacing existing Stack Sizer screening media with compatible PU panels |
| Material | Polyurethane panels, often with LANXESS raw material and customised specifications |
| Aperture | Micron or mesh size, shape, orientation matched to the required product distribution |
| Application | Fine wet screening in mineral processing, iron ore, copper ore, gold, industrial minerals |
| Service Life | Depends on formulation, feed, deck position and operating conditions |
| Benefits | Alternative procurement, potential service-life improvement, maintained screening performance |
Stack Sizer refers to a multi-deck fine wet screening machine in which several screening surfaces are arranged vertically and tensioned with a drawbolt system.
Replacement compatibility means an alternative PU panel matches the existing deck's dimensions, edge profile, tensioning arrangement and aperture specification sufficiently to install and operate without structural modification.
HT48-30 is the product designation of HTL's PU mesh panel offered for Stack Sizer replacement applications.
Mechanical fit. Deck length, width, thickness, screening-area dimensions. Edge profile must engage the drawbolt system in the correct direction, with fixing points aligned. A dimensionally close panel with a different hook profile will not tension correctly.
Aperture specification. Size in microns or mesh, shape and orientation determine cut size and separation efficiency. Effective open area determines capacity. A different aperture can fit the deck and still fail the process.
Material properties. Formulation and hardness determine wear resistance, elasticity and impact absorption. Correct specification depends on mineral abrasiveness, feed size, slurry temperature and water chemistry.
Operational fit. Deck position matters — top deck loading differs from lower decks. A single specification across all decks is not always the best configuration.
Alternative procurement reducing single-source dependency.
Potentially improved service life where formulation suits the application.
Customised screening specifications matched to cut size and product distribution.
No structural modification in many cases.
Maintained screening performance when aperture and open area match.
Cost-per-tonne improvement when service life and efficiency gains outweigh price differences.
Iron ore fines screening. Copper ore fine screening ahead of classification and flotation. Gold ore processing where screening efficiency affects recovery. Industrial minerals with tight cut sizes. Tailings duty with fine screening and dewatering. Base metal concentrators using Stack Sizer technology.
These duties sit between size reduction in CRUSHING and downstream CLASSIFICATION or DEWATERING. A panel change alters the size distribution reaching the next stage.
| Property | PU Panel (HT48-30 type) | Original OEM Polyurethane | Woven Wire Mesh | Rubber Screen Media |
|---|---|---|---|---|
| Stack Sizer compatibility | Specified configurations | Direct fit | Not applicable | Not applicable |
| Abrasion resistance | Good | Good | Moderate | Good–excellent |
| Fine aperture capability | Good | Good | Good | Limited |
| Procurement flexibility | High | Single source | Depends on supplier | Depends on supplier |
| Customisation scope | Broad | Limited | Moderate | Moderate |
| Best application | Fine wet screening replacement | Original equipment | Clean dry fine duty | Coarse impact zones |
| Scenario | Dominant Constraint | Recommended Direction |
|---|---|---|
| OEM panel lead time or price problem | Procurement | Evaluate HT48-30 type PU panel with full specification match |
| Existing panels wearing prematurely | Wear life | Review formulation and deck position before changing supplier |
| Aperture specification not met | Separation | Confirm aperture size in microns, shape and orientation |
| Edge profile differs from original | Mechanical fit | Re-measure hook profile against drawing before ordering |
| Machine previously repaired or modified | Dimensional drift | Verify actual dimensions rather than relying on original drawing |
| Fine cut with tight tolerance | Open area and accuracy | POLYURETHANE FINE SCREEN PANEL evaluation |
| Industry | Typical Material | Stack Sizer Duty | Replacement Priority |
|---|---|---|---|
| Iron ore | Hematite, magnetite fines | Fine screening ahead of classification | Wear life and aperture match |
| Copper | Copper ore fines | Grinding circuit classification | Efficiency and open area |
| Gold | Gold ore fines | Pre-concentration and classification | Cut size accuracy |
| Coal | Coal fines | Desliming and preparation | Wet handling and blinding |
| Industrial minerals | Silica sand | Fine classification | Aperture precision |
| Base metals | Lead zinc, nickel fines | Grinding circuit | Efficiency and wear |
| Phosphate | Phosphate fines | Wet screening | Blinding and drainage |
| Tailings | Slurry, fine solids | Dewatering and recovery | Slot design and wear |
Confirm the machine model. Stack Sizer models differ in deck configuration and panel dimensions.
Obtain the existing panel part number. Fastest route to the original specification.
Measure panel dimensions. Length, width, thickness, screening-area dimensions, edge and hook profile. Compare against the proposed drawing, not a product page.
Confirm the tensioning arrangement. Drawbolt configuration, tensioning direction, fixing points, seating arrangement.
Match the aperture specification. Size in microns or mesh, shape, orientation, product-size distribution, effective open area.
Confirm polyurethane properties. Formulation, hardness and filler content suited to mineral, feed, slurry and water conditions.
Check the deck for prior modification. Repaired structures may differ from original drawings.
Trial one deck before converting. Compare throughput, separation, wear and cost per tonne.
Required information: machine brand and model, existing panel part number, panel length and width, thickness, aperture size and shape, tensioning arrangement, deck position, mineral type, feed particle size, slurry conditions.
Drawings: panel outline with tolerances, aperture pattern and pitch, edge and hook profile, fixing point positions.
OEM part numbers: obtain original part number and revision references.
Material: request formulation, raw material source, hardness and abrasion test information.
MOQ, lead time, packaging, shipping: confirm trial quantity, shutdown alignment, panel packaging and shipping method.
Inspection: dimensional check, aperture measurement, hardness verification, edge profile verification.
Ask the supplier: Can you manufacture to our drawing? Can you confirm the raw material source and material reports? Can you support OEM replacement for our machine model? Do you have export experience in our region? Can you provide references for similar Stack Sizer installations? The WHICH MANUFACTURER OFFERS HIGH-QUALITY POLYURETHANE TUFFLEX WIRE SCREENS FOR MINING? guide expands on each question.
| Problem | Possible Cause | Recommended Solution |
|---|---|---|
| Panel seats poorly after installation | Edge profile or tensioning direction differs from original | Re-measure hook profile; compare against drawing |
| Panel fails at edge or fixing points | Insufficient tension; wrong fixing arrangement | Confirm drawbolt configuration and tensioning procedure |
| Aperture specification not met | Wrong aperture size, shape or orientation | Re-verify against required product distribution |
| Blinding on fine apertures | Wet fines adhesion; poor spray coverage | Review spray system and surface design; check SCREENING ACCESSORIES |
| Premature wear on a specific deck | Deck position load differs from assumed | Use position-specific panel specification |
| Panel loosens during operation | Tensioning procedure incorrect or fasteners worn | Re-tension to specification; inspect fasteners |
| Cracking at fixing points | Impact loading; panel hardness unsuited to duty | Review formulation and deck position |
| Machine previously modified | Actual dimensions differ from original drawing | Measure actual deck; manufacture to measured dimensions |
| Cost per tonne worse than OEM | Service life or efficiency lower than expected | Reassess formulation, aperture and deck position |
Daily: check panel movement, loose tension, visible wear; record deck position.
Weekly: inspect tensioning and fixing points; check aperture blockage and blinding.
Monthly: measure wear at high-wear zones; compare aperture dimensions against specification.
Wear monitoring: photograph panels by deck position at fixed intervals.
Replacement timing: plan on measured wear rate; keep spare panels sized to consumption.
Downtime reduction: pre-stage panels and drawbolt tooling before shutdown.
Preventive maintenance: treat spray system condition and feed distribution as maintenance items.
Customer Type: Mid-size iron ore processing plant with a Stack Sizer installation in a fine screening circuit.
Ore Type: Hematite fines with moderate abrasiveness.
Operating Conditions: Original OEM panels in use; procurement lead times causing scheduling pressure; panels wearing at expected rates but replacement cost rising.
Problem: Procurement single-source dependency and lead-time risk; the plant needed an alternative supply option without changing screening performance.
Solution: Technical review of the original panel specification, including dimensions, edge profile, tensioning arrangement and aperture size. HTL's HT48-30 PU Mesh Panel was proposed against that specification. A trial quantity was installed on one deck with the remaining decks unchanged.
Result: HTL reports a 20-day service-life increase and 3% screening efficiency improvement compared with the previous panels in this application. The plant gained a second supply source, which reduced procurement risk. Final conversion decisions were made deck by deck on the trial data.
Figures are supplier-reported results from a specific application, not guaranteed performance for every Stack Sizer installation.
A screen media change is a circuit change. Where the Stack Sizer receives ground product, particle-size distribution and slurry density depend on CRUSHING and upstream grinding performance. Where undersize proceeds to CLASSIFICATION, DEWATERING or FLOTATION, a change in cut size affects downstream performance weeks later. The trial should include downstream indicators, not only panel wear.
Q1: Can PU mesh panels be installed on an existing Stack Sizer?
Yes, in many cases. Stack Sizer machines are already designed to use polyurethane screening media, so replacement panels can be installed provided the dimensions, edge profile, tensioning arrangement and aperture specification match the existing deck. The compatibility check is specific to each machine model and configuration, not a general property of PU panels.
Q2: Is every PU panel a direct replacement?
No. Even a panel with the correct overall length and width can be unsuitable if the edge profile or tensioning direction differs. The hook profile, drawbolt configuration and fixing points must all match. This is why a technical drawing or physical sample is more useful than a product description.
Q3: What dimensions need checking before ordering?
Overall panel length, width, thickness, screening-area dimensions, edge and hook dimensions. Where the original drawing is unavailable, photographs from above, below and at the edges are useful, together with any identification markings.
Q4: Will the replacement panel require machine modification?
Often not. If the panel is manufactured to match the existing dimensions, edge profile and tensioning arrangement, installation without modification is usually possible. However, this should be confirmed for the exact machine, particularly if the structure has previously been repaired or modified.
Q5: What if the existing panel part number is unavailable?
Measure the panel directly and photograph the edges, hook profile and seating arrangement. Provide the machine model and deck position. For fine apertures, measure with suitable equipment rather than estimating from a photograph.
Q6: How much does a replacement Stack Sizer PU panel cost?
Price depends on panel dimensions, aperture specification, polyurethane formulation, raw material source and quantity. Compare against the OEM panel on cost per tonne rather than price per panel, and include lead time and procurement risk in the assessment.
Q7: Can HT48-30 panels be installed on all Stack Sizer models?
They are published as compatible with specified Stack Sizer installation arrangements, not as a universal replacement for every model. Confirm the specific machine model, deck configuration and panel specification with the supplier before ordering.
Q8: How long do replacement PU panels last compared with OEM panels?
Service life depends on formulation, feed, deck position and operating conditions. HTL reports a 20-day increase in one iron-ore application, which is a specific result rather than a general promise. A trial on your own deck with your own feed is the only reliable way to establish the difference.
Q9: What should I record during a trial?
Throughput, screening efficiency, product particle-size distribution, blinding or pegging frequency, panel wear and any signs of movement or damage. Also record the baseline values from the existing media before installing the trial panel.
Q10: How should I evaluate whether to convert the whole machine?
Compare cost per tonne against the existing media, including maintenance time and downtime, not only panel price. If the trial deck shows equivalent separation and equal or better service life, conversion can proceed deck by deck, with each deck evaluated against its own duty.
PU mesh panels can be installed on many existing Stack Sizer machines when they are manufactured to match the original panel dimensions, fixing arrangement, tensioning system and screening specifications. The most important step is to confirm compatibility before ordering.
Physical dimensions alone are not sufficient. Aperture geometry, effective open area and polyurethane properties must also suit the application. Where the machine has been repaired or modified, verify actual dimensions rather than relying on the original drawing.
For plants seeking an alternative replacement-media supplier, HTL's HT48-30 PU Mesh Panel is one option to evaluate. A technical review and controlled trial can verify fit, screening performance and operating value. If you are considering a replacement, HTL can review your machine details and current panel specification to discuss a suitable configuration.
Related Products
Related Technical Guides
IMPROVE FINE SCREENING EFFICIENCY WITH POLYURETHANE SCREEN PANELS
HYDROCYCLONE WEAR: ROOT CAUSES, HIGH-WEAR ZONES & MATERIAL SOLUTIONS
FLOTATION CELL ROTOR AND STATOR WEAR PARTS: HOW THEY CONTROL RECOVERY, FLOW AND MAINTENANCE COST
ROTOR & STATOR IN MECHANICAL FLOTATION CELLS: THE HEART OF EFFICIENT MINERAL FLOTATION
Related Buyer Guides
WHICH MANUFACTURER OFFERS HIGH-QUALITY POLYURETHANE TUFFLEX WIRE SCREENS FOR MINING?
HOW DO I CHOOSE THE RIGHT RUBBER BELT FOR A VACUUM BELT FILTER?
Related Comparison Articles
POLYURETHANE SCREEN VS RUBBER SCREEN VS WIRE MESH: A COMPLETE COMPARISON GUIDE
SELF-CLEANING SCREEN VS TRADITIONAL WOVEN WIRE MESH: WHICH ONE SHOULD YOU CHOOSE?
Annie Lu
Email: annie.lu@huataogroup.com
Mobile / WhatsApp / WeChat: +86 18032422676
Website: https://www.tufflexscreen.com